7 inch (180mm) Twin wall flue Dinak DW (Black)

Adapter used to change from 7 inch stove pipe to 7 inch twin wall flue. Requires a locking band.

Increasing adapter used to change from 6 inch stove pipe to 7 inch twin wall flue. Requires a locking band.

Adapter used to connect your boiler to twin wall flue. Requires a locking band.

Straight length pipe, 1000mm. (940mm effective length) Requires a locking band.

Straight length pipe, 500mm. (440mm effective length) Requires a locking band.

Straight length pipe, 330mm. (270mm effective length) Requires a locking band.

Straight length pipe, 200mm. (140mm effective length) Requires a locking band.

Telescopic adjustable pipe, 880mm - 530mm. Requires a locking band.

Telescopic adjustable pipe, 530mm - 350mm. Requires a locking band.

Telescopic adjustable pipe, 380mm - 250mm. Requires a locking band.

90 degree elbow allows for a 90 degree change in direction. Requires a locking band.

45 degree elbow allows for a 45 degree change in direction. Requires a locking band.

30 degree elbow allows for a 30 degree change in direction. Requires a locking band.

15 degree elbow allows for a 15 degree change in direction. Requires a locking band.

135 degree tee provides cleaning access at the base of the flue. Requires a locking band.

90 degree tee provides cleaning access at the base of the flue. Requires a locking band.

Tee cap is used to close off and provide cleaning access at the base of a tee. Requires a locking band.

Tee cap with drain is used to close off and provide a drain point at the base of the flue. Requires a locking band.

Locking band is used to connect two pieces together at the join.

Wall support is used to connect two pieces together at the join with its integrated locking band and fixes the chimney to the wall.

Adjustable wall support is used to connect two pieces together at the join ( with its integrated locking band) and fixes the chimney to the wall.

Cuttable wall support is used to connect two pieces together at the join (with its integrated locking band) and fixes the chimney to the wall.

Cuttable wall support is used to connect two pieces together at the join (with its integrated locking band) and fixes the chimney to the wall.

Flat wall support is used to fix the chimney to the wall. Fix anywhere except on a joint.

Flat adjustable wall support is used to fix the chimney to the wall. Fix anywhere except on a joint.

Flat cuttable wall support is used to fix the chimney to the wall. Fix anywhere except on a joint.

Flat cuttable wall support is used to fix the chimney to the wall. Fix anywhere except on a joint.

Adjustable base support is designed to be installed at the base of the vertical run of the chimney. Requires a locking band.

Adapter used to connect twin wall flue to a flue liner where the top part of your masonry chimney has been removed. Requires a locking band.

Adapter used to connect flue liner to twin wall flue where the bottom part of your masonry chimney has been removed. Requires a locking band and flue liner adapter.

Joist support is used where the flue passes through a floor or ceiling.

The roof support is designed to be fixed to the underside of the rafters.

Guy wire bracket is a special bracket to which guy wires are attached.

The Universal guy wire kit provides lateral support to the flue above the roof line. Guy wire bracket needed.

The twin wall roof brace kit provides lateral support to the flue above the roof line. Guy wire bracket included.

Firestop plate in black for use on non combustible floors and ceilings.

Stainless steel circular ceiling plate in black.

Ventilated firestop must be used on solid fuel appliances where the flue passes through a combustible floor or ceiling.

Ventilated firestop must be used on solid fuel appliances where the flue passes through a combustible floor or ceiling.

This flashing is used to provide a weatherproof seal where the flue passes through a tiled or slate roof.

This flashing is used to provide a weatherproof seal where the flue passes through a tiled or slate roof.

Lead flashing, used to provide a weatherproof seal where the flue passes through a tiled or slate roof. Roof pitches from 0 to 45 degrees.

This flashing is used to provide a weatherproof seal where the flue passes through a tiled or slate roof.

This flashing is suitable for sheet metal profiled roofs, flat roofs, boats and caravans. Comes with fixing kit.

This flashing is suitable for sheet metal profiled roofs, flat roofs, boats and caravans. Comes with fixing kit.

Select the pitch required. Lead slates are used wherever a pipe penetrates a roof, to form a weatherproof joint.

Select the pitch required. Lead slates are used wherever a pipe penetrates a roof, to form a weatherproof joint.

Select the pitch required. Lead slates are used wherever a pipe penetrates a roof, to form a weatherproof joint.

Storm collar is used as extra protection above the flashing where the flue passes through the roof.

Rain cap is the final element of the vertical run and provides protection from the rain. Requires a locking band.

Open terminal is the final element of the vertical run. Requires a locking band.

The weathering cap is the final element of the vertical run and provides protection from the wind and rain. Suitable for solid fuel and gas. Requires a locking band.

A rotating cowl especially adapted for DW twin wall.

For use with closed wood burning stoves only. Ideal for use on short flue systems.

Finishing plate is a two piece plate that covers the hole where the flue goes through the wall.

Finishing plate is a two piece plate that covers the hole where the flue goes through the wall.

Wall sleeve protects the chimney as it passes through the wall.